How To Set Time On Citizen Watch

                                  Denizen World Time Instruction Transmission E784 Abbreviated instruction

This watch is solar-powered. Expose the dial to lite and utilise it sufficiently charged.
To see details of charging fourth dimension, specifications and operations, refer to the instruction transmission: E784 instruction manual

Component identification

Setting the globe time

This scout can signal the fourth dimension around the world co-ordinate to which of 26 fourth dimension zones (offsets from UTC — Coordinated Universal Fourth dimension) is called.

Pull the crown out to position i.
The second hand points the time zone currently set up.
Rotate the crown clockwise to select an area.
The hour and minute hands start moving every bit you lot finished to select an area.
- Date indication also moves synchronously.
When the hands and indication cease, Push the crown in to position 0 to finish the procedure.

Table of fourth dimension zones and representative places

Countries or regions may alter time zones for diverse reasons.
When using the watch in an surface area not listed in the table, select an area name in the same time zone.

Setting summer time

The summer fourth dimension setting (SMT ON/OFF) y'all ready is applied to all the time zones of the world time.

ane. Push the crown in to position 0.

ii. Printing and release the button.
The second hand indicates the current summertime fourth dimension setting.

The watch returns to normal indication in x seconds without any operation during the steps beneath.

3. Rotate the crown to switch the summer fourth dimension setting (SMT ON/OFF).

Each time you rotate the crown clockwise, the setting changes alternately.

four. Press the button to end the procedure.

Setting the time and agenda

Before adjusting time and calendar, cheque the time zone of the time and calendar to set and its summer time status and accommodate the setting of globe fourth dimension and that of summertime fourth dimension (SMT ON/OFF) correctly.

Setting the time

Pull the crown out to position 2.
The 2d manus points to 0 seconds and stops.
- Adjust the reference position earlier fourth dimension and calendar aligning if the second hand does not indicate 0 seconds following the steps of "Correcting the reference position".
Rotate the crown to ready hour and minute.
- When you rotate the crown apace a few times, the paw/indication will motility continuously. To cease the rapid movement, rotate the crown in either direction.
- Engagement indication too moves synchronously. Change of date indication shows it simply became AM.
- Appointment indication does not change while moving the hands counterclockwise.
Push button the crown in to position 0 in accordance with a reliable fourth dimension source to cease the procedure.

Setting the calendar

Push the crown in to position 0.
Press and release the push button.
The second hand indicates the current summer time setting.
- Execute the side by side step inside ten seconds.
Press and concur the push for ii seconds or more than while the second hand indicates the summertime time setting.
The second hand turns fully around and indicates the current yr and month setting.
- Release the button when the 2nd hand starts moving.
- The sentinel returns to normal indication in thirty seconds without whatever operation during the steps below.
Rotate the crown clockwise to adjust the year and month setting.
· If you rotate the crown quickly a few times, the hand will move continuously. To stop the rapid movement, rotate the crown clockwise.
Rotate the crown counterclockwise to set the appointment indication.
Press the push button to end the procedure.

Correcting the reference position

Arrange the reference position when the second hand does not betoken 0 seconds while the crown is in position ii.

Ezoic

Correct reference positions:

Hour, minute and second hands: 0 60 minutes 00 minute 0 second
Date indication: "1" ON
Practice non adapt the reference position when the watch indicates 11:l PM – 12:ten AM. Otherwise, the engagement indication may change incorrectly.

Pull the crown out to position 2.
Printing and release the button.
All Reset is executed.
Rotate the crown to ready the hr and minute hands to 0 hours 00 minutes.
- If you rotate the crown quickly a few times, the hand volition motion continuously. To cease the rapid move, rotate the crown in either direction.
Push the crown in to position 1.
Rotate the crown clockwise to ready the second hand to 0 2d.
- If you rotate the crown quickly a few times, the mitt will move continuously. To end the rapid movement, rotate the crown clockwise.
Rotate the crown counterclockwise to set the date indication to "ane".
- When you rotate the crown quickly a few times, the indication will movement continuously. To stop the rapid movement, rotate the crown counterclockwise.
- Rotate the crown while pressing and holding the button to conform the position finely.
Push the crown in to position 0 to stop the procedure.
The reference position is updated and the second hand starts moving.
- Arrange the time and calendar later that.

Documents / Resources